Don’t be a watt-waster. If your computers don’t need to be on then shut them down. For convenience and nerd creds, you can configure your Linux computers to wake up and shut down automatically.
Some computers need to be on all the time, which is fine as long as it’s not about satisfying an uptime compulsion. Some people are very proud of their lengthy uptimes, and now that we have kernel hot-patching that leaves only hardware failures requiring shutdowns. I think it’s better to be practical. Save electricity as well as wear on your moving parts, and shut them down when they’re not needed. For example, you can wake up a backup server at a scheduled time, run your backups, and then shut it down until it’s time for the next backup. Or, you can configure your Internet gateway to be on only at certain times. Anything that doesn’t need to be on all the time can be configured to turn on, do a job, and then shut down.
For computers that don’t need to be on all the time, good old cron will shut them down reliably. Use either root’s cron, or
/etc/crontab. This example creates a root cron job to shut down every night at 11:15 p.m.
# crontab -e -u root# m h dom mon dow command15 23 * * * /sbin/shutdown -h now
This example runs only on weekdays.
15 23 * * 1-5 /sbin/shutdown -h now
You can create multiple cronjobs for different days and times. See
man 5 cron to learn about all the time and date fields.
You may also use
/etc/crontab, which is fast and easy, and everything is in one file. You have to specify the user:
15 23 * * 1-5 root shutdown -h now
Auto-wakeups are very cool; most of my SUSE colleagues are in Nuremberg, so I am crawling out of bed at 5 a.m. to have a few hours of overlap with their schedules. My work computer turns itself on at 5:30 a.m., and then all I have to do is drag my coffee and myself to my desk to start work. It might not seem like pressing a power button is a big deal, but at that time of day every little thing looms large.
Waking up your Linux PC can be less reliable than shutting it down, so you may want to try different methods. You can use
wakeonlan, RTC wakeups, or your PC’s BIOS to set scheduled wakeups. These all work because, when you power off your computer, it’s not really all the way off; it is in an extremely low-power state and can receive and respond to signals. You need to use the power supply switch to turn it off completely.
A BIOS wakeup is the most reliable. My system BIOS has an easy-to-use wakeup scheduler (Figure 1). Chances are yours does, too. Easy peasy.
wakeonlan is the next most reliable method. This requires sending a signal from a second computer to the computer you want to power on. You could use an Arduino or Raspberry Pi to send the wakeup signal, a Linux-based router, or any Linux PC. First, look in your system BIOS to see if
wakeonlan is supported — which it should be — and then enable it, as it should be disabled by default.
Then, you’ll need an Ethernet network adapter that supports
wakeonlan; wireless adapters won’t work. You’ll need to verify that your Ethernet card supports
# ethtool eth0 | grep -i wake-on Supports Wake-on: pumbg Wake-on: g
The Supports Wake-on line tells you what features are supported:
- d — all wake ups disabled
- p — wake up on physical activity
- u — wake up on unicast messages
- m — wake up on multicast messages
- b — wake up on broadcast messages
- a — wake up on ARP messages
- g — wake up on magic packet
- s — set the Secure On password for the magic packet
man ethtool is not clear on what the
p switch does; it suggests that any signal will cause a wake up. In my testing, however, it doesn’t do that. The one that must be enabled is
g -- wake up on magic packet, and the Wake-on line shows that it is already enabled. If it is not enabled, you can use
ethtool to enable it, using your own device name, of course:
# ethtool -s eth0 wol g
This may or may not survive a restart, so to make it a sure thing, you can create a root cron job to run the enable command after every restart:
@reboot /usr/bin/ethtool -s eth0 wol g
Another option is recent Network Manager versions have a nice little checkbox to enable
wakeonlan (Figure 2).
There is a field for setting a password, but if your network interface doesn’t support the Secure On password, it won’t work.
Now you need to configure a second PC to send the wakeup signal. You don’t need root privileges, so create a cron job for your user. You need the MAC address of the network interface on the machine you’re waking up:
30 08 * * * /usr/bin/wakeonlan D0:50:99:82:E7:2B
RTC Alarm Clock
Using the real-time clock for wakeups is the least reliable method. Check out Wake Up Linux With an RTC Alarm Clock; this is a bit outdated as most distros use systemd now. Come back next week to learn more about updated ways to use RTC wakeups.
Learn more about Linux through the free “Introduction to Linux” course from The Linux Foundation and edX.